diff --git a/src/energenie/drv/ino_ook/delay.c b/src/energenie/drv/ino_ook/delay.c deleted file mode 100644 index c704dc9..0000000 --- a/src/energenie/drv/ino_ook/delay.c +++ /dev/null @@ -1,28 +0,0 @@ - -#include -#include "system.h" -#include "delay.h" - -void delaysec(uint8_t s) -{ - int i; - for (i=0; i - -/***** CONFIGURATION *****/ - - -/***** CONSTANTS *****/ - - -/***** VARIABLES *****/ - -/****** MACROS *****/ - -//#define INP_GPIO(g) -//#define OUT_GPIO(g) - -//#define GPIO_SET -//#define GPIO_CLR - -//#define GPIO_READ(g) - -//#define GPIO_HIGH(g) -//#define GPIO_LOW(g) - - -void gpio_init() -{ - //TODO -} - - -void gpio_setin(uint8_t g) -{ - //TODO this is a temporary hack. Need to use PORT registers - pinMode(g, INPUT); -} - - -void gpio_setout(uint8_t g) -{ - //TODO this is a temporary hack. Need to use PORT registers - pinMode(g, OUTPUT); -} - - -void gpio_high(uint8_t g) -{ - //TODO this is a temporary hack. Need to use PORT registers - digitalWrite(g, 1); -} - - -void gpio_low(uint8_t g) -{ - //TODO this is a temporary hack. Need to use PORT registers - digitalWrite(g, 0); -} - - -void gpio_write(uint8_t g, uint8_t v) -{ - //TODO this is a temporary hack. Need to use PORT registers - digitalWrite(g, v); -} - - -uint8_t gpio_read(uint8_t g) -{ - //TODO this is a temporary hack. Need to use PORT registers - return digitalRead(g); -} - - -/***** END OF FILE *****/ diff --git a/src/energenie/drv/ino_ook/ino_ook.ino b/src/energenie/drv/ino_ook/ino_ook.ino deleted file mode 100644 index ea935a3..0000000 --- a/src/energenie/drv/ino_ook/ino_ook.ino +++ /dev/null @@ -1,169 +0,0 @@ -#include "gpio.h" -#include "spi.h" -//#include "trace.h" -#include "delay.h" -#include "hrf69.h" - - // pin number on Raspberry Pi (not GPIO number) -#define SPI_RESET 2 // P1-22 (active high) -#define SPI_CS 3 // P1-26 (active low) -#define SPI_SCLK 4 // P1-23 -#define SPI_MOSI 5 // P1-19 -#define SPI_MISO 6 // P1-21 - // P1-20 GND - // P1-17 3V3 - -static SPI_CONFIG spiConfig = {SPI_CS, SPI_SCLK, SPI_MOSI, SPI_MISO, SPI_SPOL0, SPI_CPOL0, SPI_CPHA0, 1000, 1000, 1000}; - -void setup() -{ - gpio_setout(SPI_RESET); - gpio_low(SPI_RESET); - spi_init(&spiConfig); - Serial.begin(19200); -} - -void reset() -{ - gpio_high(SPI_RESET); - delay(2000); - gpio_low(SPI_RESET); -} - -void test2() -{ - unsigned char wr_mode_tx[] = {0x80 |0x01, 0x0C}; // set mode register to TRANSMITTER - unsigned char rd_mode[] = {0x00 |0x01, 0x00}; // read mode register - - unsigned char rx[2]; - - reset(); - spi_select(); - spi_frame(wr_mode_tx, NULL, sizeof(wr_mode_tx)); - spi_deselect(); - - spi_select(); - spi_frame(rd_mode, rx, sizeof(rd_mode)); - spi_deselect(); - - Serial.println(rx[1]); -} - -//TODO this table should be in progmem?? -HRF_CONFIG_REC config_OOK[] = { - {HRF_ADDR_REGDATAMODUL, HRF_VAL_REGDATAMODUL_OOK}, // modulation scheme OOK - {HRF_ADDR_FDEVMSB, 0}, // frequency deviation -> 0kHz - {HRF_ADDR_FDEVLSB, 0}, // frequency deviation -> 0kHz - {HRF_ADDR_FRMSB, HRF_VAL_FRMSB433}, // carrier freq -> 433.92MHz 0x6C7AE1 - {HRF_ADDR_FRMID, HRF_VAL_FRMID433}, // carrier freq -> 433.92MHz 0x6C7AE1 - {HRF_ADDR_FRLSB, HRF_VAL_FRLSB433}, // carrier freq -> 433.92MHz 0x6C7AE1 - {HRF_ADDR_RXBW, HRF_VAL_RXBW120}, // channel filter bandwidth 120kHz - {HRF_ADDR_BITRATEMSB, 0x40}, // 1938b/s - {HRF_ADDR_BITRATELSB, 0x80}, // 1938b/s - {HRF_ADDR_PREAMBLELSB, 0}, // preamble size LSB 3 - {HRF_ADDR_SYNCCONFIG, HRF_VAL_SYNCCONFIG4}, // Size of the Sync word = 4 (SyncSize + 1) - {HRF_ADDR_SYNCVALUE1, HRF_VAL_SYNCVALUE1OOK}, // sync value 1 - {HRF_ADDR_SYNCVALUE2, 0}, // sync value 2 - {HRF_ADDR_SYNCVALUE3, 0}, // sync value 3 - {HRF_ADDR_SYNCVALUE4, 0}, // sync value 4 - {HRF_ADDR_PACKETCONFIG1, HRF_VAL_PACKETCONFIG1OOK}, // Fixed length, no Manchester coding, OOK - {HRF_ADDR_PAYLOADLEN, HRF_VAL_PAYLOADLEN_OOK}, // Payload Length - {HRF_ADDR_FIFOTHRESH, HRF_VAL_FIFOTHRESH30} // Condition to start packet transmission: wait for 30 bytes in FIFO -}; - - -// A 'go for broke' OOK payload sender -void hrf_test_send_ook(void) -{ - uint8_t payload[] = { - // Preamble - 0x00, 0x80, 0x00, 0x00, 0x00, - // Encoded 20 bit address - 0x8E, 0xE8, 0xEE, 0x88, 0x8E, 0xE8, 0xEE, 0x88, 0x8E, 0xE8, - // Command bits - 0xEE, 0xE8 // 1110 = E = switch 1 off - //0xEE, 0xEE // 1111 = F = switch 1 on - }; - - reset(); - HRF_config(config_OOK, sizeof(config_OOK)); - HRF_change_mode(HRF_MODE_TRANSMITTER); - - - HRF_pollreg(HRF_ADDR_IRQFLAGS1, HRF_MASK_MODEREADY|HRF_MASK_TXREADY, HRF_MASK_MODEREADY|HRF_MASK_TXREADY); - HRF_writefifo_burst(payload, sizeof(payload)); - - //for (int i=0; i<8; i++) - //{ - // HRF_pollreg(HRF_ADDR_IRQFLAGS2, HRF_MASK_FIFOLEVEL, 0); - // HRF_writefifo_burst(payload, sizeof(payload)); - //} - - HRF_pollreg(HRF_ADDR_IRQFLAGS2, HRF_MASK_PACKETSENT, HRF_MASK_PACKETSENT); // wait for Packet sent - - //uint8_t irqflags2 = HRF_readreg(HRF_ADDR_IRQFLAGS2); - - //TRACE_OUTS("irqflags2:"); - //TRACE_OUTN(irqflags2); - //TRACE_NL(); - //if (((irqflags2 & HRF_MASK_FIFONOTEMPTY) != 0) || ((irqflags2 & HRF_MASK_FIFOOVERRUN) != 0)) - //{ - // //TRACE_FAIL("Failed to send repeated payload"); - //} - -} - - -void loop() -{ - while (true) - { - hrf_test_send_ook(); - } -} - - - -//void setup() -//{ -// gpio_init(); -// gpio_setout(SPI_RESET); -// gpio_setout(SPI_CS); -// gpio_setout(SPI_SCLK); -// gpio_setout(SPI_MISO); -// gpio_setout(SPI_MOSI); -//} - - -//void loop() -//{ -// while (true) -// { -// gpio_high(SPI_RESET); -// delaysec(1); -// gpio_low(SPI_RESET); -// delaysec(1); -// -// gpio_high(SPI_CS); -// delaysec(1); -// gpio_low(SPI_CS); -// delaysec(1); -// -// gpio_high(SPI_SCLK); -// delaysec(1); -// gpio_low(SPI_SCLK); -// delaysec(1); -// -// gpio_high(SPI_MISO); -// delaysec(1); -// gpio_low(SPI_MISO); -// delaysec(1); -// -// gpio_high(SPI_MOSI); -// delaysec(1); -// gpio_low(SPI_MOSI); -// delaysec(1); -// } -//} - - diff --git a/src/energenie/drv/ino_ook/trace.c b/src/energenie/drv/ino_ook/trace.c deleted file mode 100644 index e69de29..0000000 --- a/src/energenie/drv/ino_ook/trace.c +++ /dev/null